When I first started playing with lattice stitches as part of the Stitch Fun series of embroidery stitch tutorials, I was moving towards laced lattice stitches, because they’re a little more difficult to figure out than regular lattice work.

So, we mixed up the lattice stitch tutorials with a few tutorials on lacing regular stitches, remember?

Now, we’re going to combine the concept of lattice stitches and lacing stitches to produce a raised, detached filling that can be lacy, light, and lovely. Laced lattice stitches offer a lot of leeway for experimentation – you can mix up thread types, colors, and lacing techniques to produce a variety of different effects with lattice fillings. You are limited only by your imagination here, so feel free to play about with laced lattice stitches and have a bit of Stitch Fun!

We’re going to look at two or three different laced lattice stitches, and this first one is the simplest. In the photo above, the pink stitches are laced in and out of the intersections formed by the laid stitches in the lattice. So let’s see how it’s done…

1. The Lattice Grid

First, you have to work up your lattice grid. We’ve already covered how to do this with other lattice stitches we’ve explored, so you’re already familiar with how easy this step is!

If you’re unsure of how to work the laid stitches for the grid, refer to the Stitch Fun article on Griffin Stitch, where you’ll find a photo tutorial on laying stitches for the initial lattice grid.

Stitch a lattice grid either on the diagonal or square – it doesn’t really matter. For practice, you’ll want a square grid, but you’ll be turning it on the diagonal to work the lacing.

I stitched a more-or-less square grid on the diagonal of the fabric, but you can stitch yours with horizontal and vertical laid stitches that are parallel and perpendicular to the weave of your fabric, if you wish. Like I said, it doesn’t really matter.

What you want to end up with, no matter how you do it, is a grid of lines that are perpendicular to each other.

2. Understanding Lacing Rows

Once your grid is stitched, it’s time to start lacing! Before we move ahead, though, let’s look at what is meant by “row” when lacing in this particular manner.

A “row” of lacing comprises all the intersections that line up with the side intersection where you begin stitching, plus all the intersections immediately above that line of intersections.

In the photo above, row #1 is in red, and it begins on the first red line farthest to the left, which is lower than the second red line. As the row progresses across to the right, you move up an intersection and then back down.

Row #2 in blue begins on the right, on the lowest stitch on the right, and progresses left, stepping up an intersection (shared with row #1) and then back down to the base of row #2.

So, each “row” is really made of up two rows of intersections, and you can see that row #1 in the photo above shares some intersections with row #2.

Sounds confusing? Never fear! Let’s work through it together.

3. Lacing – 1st Row, Left to Right

We’ll work step by step through two rows, so you can see how the stitch works out.

Turn your lattice so that you are working with the lattice lines running diagonally. It’s easier to work each row this way.

Bring your needle up in the fabric, just to the left of the second intersection down from the top, on the left side of the lattice. The arrow points to the place your needle should emerge for the first row.

Crossing over the first intersection to the right of where you emerged, take the needle under the lattice as shown, without picking up any fabric.

Now cross over the very top intersection on the grid, and bring the needle under the lattice as shown, without picking up any fabric.

Note: when passing under a lattice line, make sure you are only passing under one lattice line. If you pass under two, you’ll end up in the wrong place!

Now pass your needle over the last intersection in the row, over on the right, and go down into the fabric.

This ends row one! That was easy, right?

4. Lacing – 2nd Row, Right to Left

For row 2, we’re going to work back in the other direction, moving from right to left.

After completing row 1 and taking your needle to the back of the fabric, move down one intersection, and bring your needle up to the right of the intersection on the right side of the lattice, as shown in the photo above.

Cross over the intersection and pass the needle under the lattice line, as shown above, without taking up any fabric.

Now, pass over the next intersection to the left (which is shared with row 1), and take the needle underneath the lattice line, as shown in the photo above.

Tip: You’ll find that the stitch is worked the same, whether you are right or left handed. One direction of lacing will always be easier, though, depending on your dominant hand. If it helps, you can rotate your hoop in one direction or the other, to make it easier to pass the needle under the lattice lines.

Now, move down to the next intersection on the left of your last pass, cross over it, and pass the needle up and under the lattice line, as shown. This step will take you back up to the intersection shared with row 1.

Cross over the intersection shared with row 1, and take the needle down and under the lattice line as shown. You’re now ready to cross over the last intersection in row 2, on the far left.

Cross over the last intersection in row 2 (which is beyond the last intersection on row 1, because the grid widens with each row), and take the needle down into the fabric right next to the intersection, to end row 2.

5. Beginning Row 3 & Repeats

Now, we’ll begin row 3, and then – the rest is easy!

To begin row 3, step down to the next intersection on the left, below the end of row 2.

And guess what happens now?

Right! Repeat!

The rest of the lacing is done by repeating the same movements in either row 1 or row 2, depending on which side of the grid you’re on. Each row will get a little longer as the grid widens out, but it matters not – just follow the same movements across the row, and you’ll end up with this:

And eventually, that will turn into this:

And eventually, you’ll fill the whole grid.

Applications

This laced lattice stitch can be used anywhere you want to add a detached filling to your surface embroidery projects. It doesn’t have to be worked in a square shape, either, so if you want to add it to a lattice sampler, feel free!

Here, I’ve worked it in one of the little scrolls on this sampler – it’s the one on the right in the photo above. Instead of using a highly contrasting thread color, I used a slightly lighter shade of salmony-red, so the effect is subtle.

First and foremost, the job of the lacing is to hold the lattice stitches in place. You can use the same color thread as the lattice thread, if you don’t want any contrast. But if you want, you can mix up your colors all around – and your thread types – and really have fun with lacing your lattices!

Questions? Comments? Suggestions? Have your say below!

Stitch Fun is a series of embroidery stitch tutorials here on Needle ‘n Thread, where we explore different stitches just for the fun of it. If you’d like to participate in the series and work up your own sampler of stitches or learn how to apply some fun stitches to your current embroidery project, you’re most welcome to visit the Stitch Fun Index, where you can find links to all the tutorials in the series!